Home > News > Content

New Power Tools Carbon Brush For AEG Note The Details When Installing

Sep 11, 2017

New Power Tools Carbon Brush for AEG Note the details when installing
The new Power Tools Carbon Brush for AEG should be used before the grinding of the arc, grinding radian is generally carried out on the motor. Place a fine glass of sandpaper between the Power Tools Carbon Brush for AEG and the commutator. Under normal spring pressure, grind the brush in the direction of rotation of the motor. The sandpaper should stick the commutator as much as possible until Power Tools Carbon Brush for AEG arc surface coincidence, and then remove the sandpaper, with compressed air blowing dust, and then wipe clean with a soft cloth.
   Grinding the Power Tools Carbon Brush for AEG should not use emery paper to prevent the corundum particles from being embedded in the commutator slots and to scratch the surface of the brush and commutator when the motor is running. After grinding, the motor runs at 20% -30% for several hours, allowing the Power Tools Carbon Brush for AEG and commutator to run and create a uniform oxide film. And then gradually increase the current to the rated load.
    Commutator is an important part of a DC motor that converts the DC current from the Power Tools Carbon Brush for AEG to an alternating current within the winding or to a winding The AC electromotive force is converted into a DC electromotive force structure on the Power Tools Carbon Brush for AEG, and the commutator is a rounded several contacts that connect each of the contacts on the rotor and the two electrodes Called the Power Tools Carbon Brush for AEG, and touch only two of them. Power Tools Carbon Brush for AEG and commutator repeat, DC idea turned up.
    Power Tools Carbon Brush for AEG can greatly reduce the test power capacity is the need to rotate the mechanical equipment, transmission current signal, often through the center of the receiver, the center of the receiver is a copper inner slip ring. The external is installed with Power Tools Carbon Brush for AEG brush holder, when rotating, Power Tools Carbon Brush for AEG slide on the slip ring, you can ensure that the signal and power transmission, not because the cable transmission because of excessive rotation and stir The
 The current also affects the wear of the Power Tools Carbon Brush for AEG. In general, the current flowing through the Power Tools Carbon Brush for AEG is much larger than the current flowing through the negative Power Tools Carbon Brush for AEG, which can cause positive power. Power Tools Carbon Brush for AEG wears more wear than the negative Power Tools Carbon Brush for AEG. And the wear of the positive slip ring is also more than the negative slip ring, then each time the unit overhaul, we can adjust the Power Tools Carbon Brush for AEG positive and negative cable head to achieve the purpose of delay wear.
Power Tools Carbon Brush for AEG is also a material that can affect the wear of the Power Tools Carbon Brush for AEG. Different Power Tools Carbon Brush for AEG manufacturers and different Power Tools Carbon Brush for AEG models whose composition and structure are not the same, then the Power Tools Carbon Brush for AEG wear rate will not be the same. So we recommend that the majority of customers try to choose the same Power Tools Carbon Brush for AEG, because it can reduce the product model and the resulting Power Tools Carbon Brush for AEG uneven self-wear rate.
    Brush motor inside the top of the inverter surface, the motor rotation, the power through the inverter delivery to the coil, because its main component is carbon, called Power Tools Carbon Brush for AEG, it is easy to wear. Should be regularly replaced and cleaned up.
Power Tools Carbon Brush for AEG is an extremely damaging tool, so it is worthwhile to study its construction so that we can make better maintenance and replacement.
   Power Tools Carbon Brush for AEG is a device for transferring energy or signals between a fixed part of a motor or generator or other rotating machine. It is usually made of pure carbon and coagulant. It is usually a square, On the bracket, there is a spring to press it on the shaft, such as oil drilling is completed, the need for testing, it is necessary to put the instrument from the wellbore, is through the Power Tools Carbon Brush for AEG signal from the rotation to the ground The